@MrScriptster
you will get more Information about “cutting and material thickness” on my homepage
jtronics.de
but Sorry … in moment ist only in german, but I think it’s possible to understand with goggle translate
Laser + Lasertreiber mindestens 100€
einen alten Plotter bekommt man für 100 bis 200 euro
der umbau kostet nochmal um die 50 euro.
… außer man hat eh schon alles da.
Sorry for my non-existent German. Is this craft foam you are cutting? What thickness? I’m cutting 2mm foam (and 3mm if black) with a 200mW 650nm (visible red) laser LED ) at approx 50mm/min (I’d say 5-10 times slower than yours) and wanted to cut 6mm foam for a project but no matter how I slow it down, it never actually cuts 6mm – the material begins to melt instead of evaporating and never burns all the way through. I guess, it’s time to upgrade to 1W
Die Aufhängung vibriert nicht, da es ein Plotter mit einem sehr steifen Rahmen ist.
Das Verfahren macht der Diode auch nichts, da gibt es Anwedungen mit viel schlimmeren Bedingungen.
Die Diode ist jetzt auch schon seit mehreren Tagen im Betrieb, von daher kann es nicht so schlimm sein.
Der Laser hat wirklich eine Wellenlänge von 908nm. Das leuchten kommt durch die sehr hohe Energiedichte und durch den Videochip der Kamera.
Sind das wirklich 908nm? das sieht eher nach UV-Laser aus 405nm, oder so was in der Art…
Die Aufhängung mit dem Laser vibriert doch ziemlich stark wenn er schneidet, oder? Meines Wissens sind Laserdioden ziemlich anfällig gegen Vibrationen und Stöße. Ein FASER wäre demnach vielleicht geeigneter.
@MrScriptster
you will get more Information about “cutting and material thickness” on my homepage
jtronics.de
but Sorry … in moment ist only in german, but I think it’s possible to understand with goggle translate
@MrScriptster
more Information about “cutting and material thickness”
Sorry … in moment ist only in german, but I think it’s possible to understand with goggle translate
Laser + Lasertreiber mindestens 100€
einen alten Plotter bekommt man für 100 bis 200 euro
der umbau kostet nochmal um die 50 euro.
… außer man hat eh schon alles da.
wie viel kostet so ein teil?
can you cut with paper with it ? what kind of focusing tech did you use ?
how much is the machine to buy? the one in the video
Sorry for my non-existent German. Is this craft foam you are cutting? What thickness? I’m cutting 2mm foam (and 3mm if black) with a 200mW 650nm (visible red) laser LED ) at approx 50mm/min (I’d say 5-10 times slower than yours) and wanted to cut 6mm foam for a project but no matter how I slow it down, it never actually cuts 6mm – the material begins to melt instead of evaporating and never burns all the way through. I guess, it’s time to upgrade to 1W
Hello Mr, this machine your, it make rubber stamp ( rubber to trodat ) ?
Die Aufhängung vibriert nicht, da es ein Plotter mit einem sehr steifen Rahmen ist.
Das Verfahren macht der Diode auch nichts, da gibt es Anwedungen mit viel schlimmeren Bedingungen.
Die Diode ist jetzt auch schon seit mehreren Tagen im Betrieb, von daher kann es nicht so schlimm sein.
Der Laser hat wirklich eine Wellenlänge von 908nm. Das leuchten kommt durch die sehr hohe Energiedichte und durch den Videochip der Kamera.
Sehr schön! Selbst entworfen und gebastelt?
Wieso muss er das Werkzeug holen und wegschaffen?
Sind das wirklich 908nm? das sieht eher nach UV-Laser aus 405nm, oder so was in der Art…
Die Aufhängung mit dem Laser vibriert doch ziemlich stark wenn er schneidet, oder? Meines Wissens sind Laserdioden ziemlich anfällig gegen Vibrationen und Stöße. Ein FASER wäre demnach vielleicht geeigneter.